Posted on

RG Aile Strike Build Day 9

Joint and Fist Separated

Introduction

Welcome to “RG Aile Strike Build Day 9” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

I am taking my time to ensure I clean up all the marks that can be cleaned up. As with any build like this, if you end up with discolouration or a small white “stress” mark you are likely to need painting to get rid of those. I may have a look at simple quick methods of dealing with those items, especially as I find that it has a habit of happening on the grey pieces. I also accept I may need to work on my cutting style as I’m sure that will contribute to it!

The Process

Unless otherwise noted I followed this process for each piece:

  • Cut off roughly leaving plenty of nub
  • Trim back the nub with my better nippers
  • Apply water to my wet and dry sandpaper and sand the nub marks down
  • Dry the piece
  • Brush it off with the tooth brush to remove any bits
  • Re-apply the matt finish using the Gray Balancer
  • Prep the part with the green side of the White Balancer
  • Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

The Parts

Nubbed Arms Parts
Nubbed Arms Parts

As you can see the arm consists of 16 core pieces. Above I have just cut them out roughly ready for trimming and cleaning up. I showed that in the previous arm, so in this post I’m going to show you something different about them.

The arm Skeleton

On the inside you have a lovely inner frame. The frame or skeleton comes pre-case on the runner. I find it mind boggling how they cast these intricate pieces.

In the first image you can see that the fist and joint have been separated. They come attached, but you need to remove them. The top joint is actually part of the shoulder assembly used when you build the torso. The fist is just re-attached later on. Previously I had issues removing the top part, however, knowing it was a straight peg I felt far more confident twisting and pulling to free the part. I found removing it on this arm a lot easier than on the first one.

In the second image (incorrectly titled all pieces straight) I had rotated and bent the socket joint into place.

The third image then has a small piece on the left hand side of the image bent upwards. Ultimately this clips back onto the central core of the arms frame. You can see this in the next image (“Bending into place”) how the section is bending up back towards the central part of the arm frame.

The “Top connected” picture shows the left hand piece completing the motion up and clicking into place into the frame, as well as the bottom section starting to bend down.

The final image has the arm frame complete with the part the fist was attached to moved all the way flat with the rest of the frame, and in place.

The finished Arm

As with the other pictures (yes I know I need a better background, I am working on it honest!) you can see how the armour has cleaned up nicely. I am really happy again with how this fits together. I really enjoy building the arms on this model as it is a satisfying process.

Conclusion

Everything in the build process, so far, has lived up to my expectations. The detail is stunning, the precision is what I expect from Bandai, and the build itself is an incredibly enjoyable process.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

Advert / Stock 26/02/2023

MG_ASTRAY_RED_4

Welcome to “Advert / Stock 26/02/2023” by weekly update on the stock available, and the links to get you filtered on the types of models you are interested in.

Model Kits Ltd is a UK based small independent retailer.

I started the company with a single aim. To try and help get models / kits into the hands of UK builders so that they can enjoy their hobby.

I have a range of HG/RG/MG kits such as the MG Astray Red Frame available here https://modelkitsltd.co.uk/…/mg-gundam-astray-red…/

MG_ASTRAY_RED_4
MG Astray

I also have a stock of the GUNPRIMER Balancers and some of the other GUNPRIMER products, as well as a supply of reasonably priced basic bases.

If you are thinking about picking up something new, or just want to have a browse for some inspiration please consider us as an option.

I am continuing to increase the breadth of stock available in the shop as items become available; including, but not limited to, adding an MGEX Strike Freedom when the box arrives. I had 3 but 2 have already been accounted for.

Thank you everyone for your support so far, and I hope you have a great week building!

The links to individual sections / filtered list items are below.

HG Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=hg

RG Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=rg

MG Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=mg

SD Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=sd

EG Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=eg

FM Kits

https://modelkitsltd.co.uk/shop/?swoof=1…

PG Kits

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=pg

Tools

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=tools

Bases

https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=bases

Thank you for your support, and for getting to the end of “Advert / Stock 26/02/2023”!

Posted on

RG Aile Strike Build Day 8

Outside Arm

Introduction

Welcome to “RG Aile Strike Build Day 8” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

I am taking my time to ensure I clean up all the marks that can be cleaned up. As with any build like this, if you end up with discolouration or a small white “stress” mark you are likely to need painting to get rid of those. I may have a look at simple quick methods of dealing with those items, especially as I find that it has a habit of happening on the grey pieces. I also accept I may need to work on my cutting style as I’m sure that will contribute to it!

The Process

Unless otherwise noted I followed this process for each piece:

  • Cut off roughly leaving plenty of nub
  • Trim back the nub with my better nippers
  • Apply water to my wet and dry sandpaper and sand the nub marks down
  • Dry the piece
  • Brush it off with the tooth brush to remove any bits
  • Re-apply the matt finish using the Gray Balancer
  • Prep the part with the green side of the White Balancer
  • Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

Todays Parts

Nubbed Parts
Nubbed Parts

I decided to take a slightly different approach tonight as I knew I could finish this arm off. Taking this approach also allowed me to take less photos which sped the process. Again I may look into getting some sort of setup to help with that. However, at the moment I only have my phone, table, and patience 🙂

Clean Parts
Clean Parts

So, as I knew I was approaching this differently, I also cleaned up all the parts I had to work with tonight. I actually found this a nice change to the pace. Rather than cut 2 – 3 pieces, clean them, put them together, photograph them, rinse and repeat, I found doing multiple sets of pieces together meant when it came to the assembly I could just enjoy the build of the arm.

The Build

As I had approached it differently I had multiple bits to put together. Building this arm up was a really excellent experience. Seeing the parts layer on top of one another, and finally forming into the arm was a really enjoyable experience. I did have to consult the manual a couple of times, and work out which bits went where, but when in the right place the went together beautifully.

I have said it before in this build, and I’m sure I will say it again, but the armour on this build is an absolute pleasure to work with. The way the white parts clean up when you have that little bit extra time on them, they look really stunning.

As can be seen in the pictures above, the arm, in my opinion has come out really cleanly.

Articulation

The other main thing on these parts, after how stunning and detailed they are, is the articulation you get with these pieces.

Inside Arm
Inside Arm
Outside Arm
Outside Arm

As can be seen in the images above, the arm has solid articulation as well. Bending nicely, allowing for various poses.

Conclusion

So in summary. So far I have the legs, waist and an arm. However, there is not a piece in there at the moment that I am not happy with. The build has been really smooth and enjoyable so far. Apart from me wanting to examine by technique on removing the grey pieces from the sprues, I am super happy with this. I definitely think that extra bit of time, and making use of the GUNPRIMER Balancers really does make it shine.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

Lightening Stock Update 21/02/2023

RG_WING_ZERO_EW_2

So this should, again, have been the next step in the Aile Strike build, but I have just sorted my next invoice and wanted to share some details! So instead of that, welcome to “Lightening Stock Update 21/02/2023”!

On the HG side I will have the ChuChu Demi Trainer, the Dilanza Standard, Dom RickDom, G Armour, GM Command Space, GM Sniper II, Gundam Psycho, Guncannon RX-77-2 Revive, and Kampfer.

That is just the HGs that are coming in. As normal as a small company slowly growing I will have limited numbers of items so if there is something there you are interested in then you will want to be on the ball!

I will also have the MG DeathScythe coming in.

DEATHSCYTHE
DEATHSCYTHE

Again this is an absolutely awesome looking model. It looks outstanding!

Talking of MG models I will also hopefully have a spare MGEX Strike Freedom looking for a home. So if that is your sort of thing then you may want to get on that one as I’m sure that will go fast.

On the RG side, I will be having the GOD, Exia, RX-78-2, Wing, Wing XXXG-01W EW, OO QANT. Z’Gok Char Custom, Zaku II MS-06F and Zaku MS-06S also coming in.

Conclusion

As always the invoice is paid, I just need it to ship. Now as you all know I tend to have what I lovingly call hit and miss luck with UPS packages coming in to the country. However, I’m going to be hopeful that this is a smooth one and I will be seeing these all very soon!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

RG Aile Strike Build Day 7

Fitted Parts

Introduction

Welcome to “RG Aile Strike Build Day 7” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

Round about now you are probably thinking to yourself … blimey he is not a fast builder I would have had that done days ago! However, in my defence I am working full time, plus running my company, and then building after I have done everything for those. I am also really taking my time, and if I’m not happy re-visiting parts and re-doing them. I used to take months to paint a single model, to the point where my friend offers to paint them for me so that he can play against painted minis 😀 (Thank you Steve 🙂 )

So my normal steady pace aside, I do want to really enjoy the build and not rush at any stage. I want to show how stunning the model is, not just to build, but how beautifully clean it looks once complete.

Without further ado, lets just outline my process on each part so that I don’t repeat is throughout the post 🙂

The Process

Unless otherwise noted I followed this process for each piece:

  • Cut off roughly leaving plenty of nub
  • Trim back the nub with my better nippers
  • Apply water to my wet and dry sandpaper and sand the nub marks down
  • Dry the piece
  • Brush it off with the tooth brush to remove any bits
  • Re-apply the matt finish using the Gray Balancer
  • Prep the part with the green side of the White Balancer
  • Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

So this section is the build up of the arms. The first thing I had to do was build up the two shoulders. Then it steps into building each arm individually. The core of the shoulder is really simple but the plastic cleans up from the nubs really nicely and fits together nicely.

Second Parts

Next up is the armour that wraps around the core of the shoulders. Now I love these shite armour pieces. With the GUNPRIMER Balancers they clean up so nicely and shine back up to new. The pictures show how clean these pieces end up after a little TLC even given those horrendous first rough cuts of mine!

Third Parts

Ok there is no running away from it. These are, for me at least, not my favourite part of any build. I can, however, appreciate the quality and skill that has gone into making these pieces. The articulation and the fact they are moulded like this on the runner.

However, I just don’t like these bits. Thankfully once they are done it will be back to the bits I enjoy. The first image shows exactly how the piece comes off the runner. Pay very close attention to the manual, and where it says to cut. I then had to detach the hand, and the top part.

As you can see I managed to detach more than I was meant to, so I had to reattach the joint. However, I really didn’t enjoy getting the top piece out. Once that was done, all I had to do was twizzle and push bits into place. I have to admit I do enjoy that bit.

You have to pay special attention to the piece that in the first image is on the right hand side. That teeny piece actually bends in the middle, and the outer piece actually forms the part that clicks into place when you bend the rest up.

Fourth Parts

Ok so this was the last bit I got to work on. The upper arm armour. Again, this shows the detail, the layering of parts to add more detail, and the beautiful way the parts clean up. I know I have said it before but, I am very happy with the way this has been cleaning up so far!

Conclusion

I am really enjoying the build, and the pace. The parts are cleaning up beautifully and the parts are all cleaning up so nicely. That concludes “RG Aile Strike Build Day 7”.

If you wanted to pick up an RG Aile Strike to do the build yourself at the time of writing I have a few in stock available here. I also currently have both the Gray and White Balancers in stock (Gray White).

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

RG Aile Strike Build Day 6

Side waist and legs

Introduction

Welcome to “RG Aile Strike Build Day 6” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

If you want to skip that and just get up to speed. I had in previous posts gone on about how nice I think the RG Aile strike model is. I had gone on so much I decided I should put my money where my mouth was and build one myself. This ongoing series is that process. I am not rushing, as can be seen in the earlier parts, and if I am not happy I will go back, disassemble and re-clean and re-build anything I am not happy with.

With that all out of the way lets get to it!

The process

Unless otherwise noted I followed this process for each piece:

  • Cut off roughly leaving plenty of nub
  • Trim back the nub with my better nippers
  • Apply water to my wet and dry sandpaper and sand the nub marks down
  • Dry the piece
  • Brush it off with the tooth brush to remove any bits
  • Re-apply the matt finish using the Gray Balancer
  • Prep the part with the green side of the White Balancer
  • Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

So the first part off the runners is the main body of the waist. It has this piece attached / in it in the runner. The manual has an arrow showing to pull that piece out. I’ll be honest that was the hardest part of the build so far. With how detailed the pieces are I was worried about breaking it. In the end I decided to spin and twist. The turning of the part helped free it up and eventually it came out. However, I could see it causing a problem for some younger builders. However, on the whole it wasn’t “bad”.

Second Parts

Next up was the start of building up the armour on the waist. Now these pieces were nice and therapeutic. I used the process above, and am extremely happy with how the armour is coming out on this model.

Third Parts

Again, the armour is building up nicely. Even the small blue piece cleaned up perfectly. The grey piece looks a lot cleaner after a brush btw (sorry about that). However the nubs are a thing of the past and the piece looks really clean. None of the parts have had any issues going together and feel really nice.

Fourth Parts

I found these parts really satisfying to put together. There aren’t too many of them, and the slight colour differences on some of them add a nice level of contrast. They click together nicely and come together really cleanly.

The final leg

Putting all these things together you can see you have a really striking lower part of the model. All of the pieces so far have been really enjoyable to clean up and put together. There is a center grey piece that goes on top of the main waist part. I admit that is my least favourite part so far. It doesn’t want to clean up properly and just feels very meh. That part has some twisty around pre cast joints that click on to outer side armour. That goes in really snugly once you get it to click in, but getting it to click in was the “hardest” part of the build so far. However, that all said it wasn’t really hard.

Conclusion

That concludes todays “RG Aile Strike Build Day 6”. Remember if you want the model it is available (at time of writing) here.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

Advert / Stock 19/02/2023

Airbourne

Welcome to “Advert / Stock 19/02/2023”. A post that does what it says on the tin.

I have had a fairly quiet week this week stock wise, leading to the opportunity to sort some other pieces. I have, however, listed some basic stands for sale. They are £2 each. I will be honest, they make more sense to get with a model so the postage is already covered.

I think they are quite flexible and allow you do do all sorts with your 1/144 scale models. You can find them here.

The look like this.

Gundam Stand
Gundam Stand

Here are a few pictures of one of my models taking advantage of the stand!

Please excuse my photography skills, I am working on it, but I just need some time to sit down and work on it!

I am also continuing to work on my build of the RG Aile Strike. You can buy yours here. So far it is living up to expectations and building beautifully.

I have been looking at some of the Moderoid pre-orders. At the moment the following are on pre-order:

https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90583
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90587
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90267
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90647
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90648

If you would like me to put in a pre-order to see if I can get any of them let me know!

That is is for “Advert / Stock 19/02/2023”, I will update further when I get more updates!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

RG Aile Strike Build Day 5

Side Legs

Introduction

Welcome back to “RG Aile Strike Build Day 5”! After yesterdays little break, I’m back with the latest update. For anyone catching up, I have made a few posts saying how fantastic I thought the RG Aile Strike model is. However, I hadn’t actually built one yet. So I decided it was time for me to put my money where my mouth was.

This series is documenting my build of the Aile Strike along with plenty of pictures.

The Update

Ok well today I was working on the other leg, as Day 4 was the first leg. As this is a carbon copy of the previous post (you can find it here) I didn’t do all the pre and post nub cleaning pictures. Feel free to check out yesterdays post to catch up on that. Again, I can’t say how great the Gray and White Balancers are from GUNPRIMER. They really help polish parts back up to a fantastic finish.

As you can see from the pictures these parts have also come together really nicely. So far the build hasn’t had anything other than nicely fit together sections. The detailing on the neg parts is brilliant, and I can’t wait to do the panel lining on this model. I think it might take me a while though with all those bits!

Conclusion

I believe the next part is the waist. I often find these sections some of the least interesting parts to build, so I am looking forward to seeing how this one holds up. So far, this build has been a pleasure, and the outer armour has been cleaning up beautifully. Possibly my only niggle so far is I could argue the feet feel a little weird. But once posed the look brilliant.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

Build Intermission

Falling HG

Ok I admit I didn’t do any building last night. I had so many things on it just got skipped. So this is a mini intermission between the build parts.

Of course that leaves me with the question of what to do to fill the blog! Well thankfully I had a little something in my back pocket.

So I have been trying to work out how to take better photos of my kits. Again, I feel there are going to be a lot more posts on this topic as I learn more.

So before I leap in to what I was playing with let me show you the starting picture.

Ok well after searching my hard drive and my network storage apparently I didn’t keep my original image.

So lesson number 1: Remember to keep the original image!

I will, however, try and describe it.

I posed by RX80-BR figure on one of my stands in front of a green screen. Then I took some pictures. After moving them to the laptop I proceeded to open them up in GIMP and choose what I wanted to work with. After filtering through the images I picked my favourite and got to work.

First I had to set up an alpha channel. Then I used the colour select to select the green and remove a load of it. This highlighted lesson number 2. Lighting is all important. Without good lighting making everything consistent you end up with different shades and bits and pieces of green left. I then moved onto my second tool of choice. I zoomed in and proceeded to use the multi select tool to trace the edges and remove any colour too close to the model.

After an hour or twos work I finally had something I could work with … wait I may be able to show you …

No Background!
No Background!

This brings me to lesson number 3. Always do things in layers, that way you can add and remove them from the view, or even junk them and start again if needed.

My final step was to select a background and add a blur to it. This gave me the final image which looks like this.

Falling HG
Falling HG

For a first attempt I was quite happy with this. I think it is something that I would enjoy working on improving, and coming up with more ideas for.

If you would like me to do a post in more detail on the GIMP steps I used, and the whole process let me know. I can do a step by step guide for beginners (like me).

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on

RG Aile Strike Build Day 4

RG Aile Strike Leg

Introduction

Welcome to “RG Aile Strike Build Day 4” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

If you want to skip that and just get up to speed. I had in previous posts gone on about how nice I think the RG Aile strike model is. I had gone on so much I decided I should put my money where my mouth was and build one myself. This ongoing series is that process. I am not rushing, as can be seen in the earlier parts, and if I am not happy I will go back, disassemble and re-clean and re-build anything I am not happy with.

With that all out of the way lets get to it!

The process

Unless otherwise noted I followed this process for each piece:

  • Cut off roughly leaving plenty of nub
  • Trim back the nub with my better nippers
  • Apply water to my wet and dry sandpaper and sand the nub marks down
  • Dry the piece
  • Brush it off with the tooth brush to remove any bits
  • Re-apply the matt finish using the Gray Balancer
  • Prep the part with the green side of the White Balancer
  • Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

As you can see the next thing to build was this leg. The inner frame is straight off the runner. You need to take your time on this. The manual shows you the bits you want to cut. Pay special attention to this as the nubs are tiny and you don’t want to snip anything by accident. The first two parts go on either side of the leg. They clip right on and fit really nicely.

Second Parts

The next pieces start to attach the armour. As you can see I was leaving healthy nubbage on each piece. I followed the process outlined at the top of the article. Once clean, and seated I moved on to the next armour parts.

Third Parts

As you can see this section is adding more armour on to the frame. Each piece fits really nicely. I did have to slow down and double check how everything was sliding in to place. But after slowing myself down a little it all slotted together really nicely. Again I was really happy with how the white armour pieces were cleaning up.

Fourth Parts

Next … you guessed it more armour parts. Each one I’ve tried to show the nubbed parts and the cleaned parts. Hopefully the end result warrants all this time … I feel that it is looking really nice so far.

Fifth Part

The final set of armour pieces on the leg really do complete the piece. Also look at that articulation!

Conclusion

There are several parts here that have to slide or clip into specific places. However, I found that slowing down, have a close look at the manual, the structure of the grooves and ridges on the parts led to them fitting together beautifully. I am really happy with how the parts have cleaned up, and the current state of the leg.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk