ModelKitsLtd.co.uk

Posted on February 20, 2023February 19, 2023 by Mark

RG Aile Strike Build Day 6

Introduction

Welcome to “RG Aile Strike Build Day 6” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

If you want to skip that and just get up to speed. I had in previous posts gone on about how nice I think the RG Aile strike model is. I had gone on so much I decided I should put my money where my mouth was and build one myself. This ongoing series is that process. I am not rushing, as can be seen in the earlier parts, and if I am not happy I will go back, disassemble and re-clean and re-build anything I am not happy with.

With that all out of the way lets get to it!

The process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

Waist and detached thingy — Waist and thingy

So the first part off the runners is the main body of the waist. It has this piece attached / in it in the runner. The manual has an arrow showing to pull that piece out. I’ll be honest that was the hardest part of the build so far. With how detailed the pieces are I was worried about breaking it. In the end I decided to spin and twist. The turning of the part helped free it up and eventually it came out. However, I could see it causing a problem for some younger builders. However, on the whole it wasn’t “bad”.

Second Parts

Next up was the start of building up the armour on the waist. Now these pieces were nice and therapeutic. I used the process above, and am extremely happy with how the armour is coming out on this model.

Third Parts

Again, the armour is building up nicely. Even the small blue piece cleaned up perfectly. The grey piece looks a lot cleaner after a brush btw (sorry about that). However the nubs are a thing of the past and the piece looks really clean. None of the parts have had any issues going together and feel really nice.

Fourth Parts

I found these parts really satisfying to put together. There aren’t too many of them, and the slight colour differences on some of them add a nice level of contrast. They click together nicely and come together really cleanly.

The final leg

Putting all these things together you can see you have a really striking lower part of the model. All of the pieces so far have been really enjoyable to clean up and put together. There is a center grey piece that goes on top of the main waist part. I admit that is my least favourite part so far. It doesn’t want to clean up properly and just feels very meh. That part has some twisty around pre cast joints that click on to outer side armour. That goes in really snugly once you get it to click in, but getting it to click in was the “hardest” part of the build so far. However, that all said it wasn’t really hard.

Conclusion

That concludes todays “RG Aile Strike Build Day 6”. Remember if you want the model it is available (at time of writing) here.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 19, 2023February 19, 2023 by Mark

Advert / Stock 19/02/2023

Welcome to “Advert / Stock 19/02/2023”. A post that does what it says on the tin.

I have had a fairly quiet week this week stock wise, leading to the opportunity to sort some other pieces. I have, however, listed some basic stands for sale. They are £2 each. I will be honest, they make more sense to get with a model so the postage is already covered.

I think they are quite flexible and allow you do do all sorts with your 1/144 scale models. You can find them here.

The look like this.

Here are a few pictures of one of my models taking advantage of the stand!

Please excuse my photography skills, I am working on it, but I just need some time to sit down and work on it!

I am also continuing to work on my build of the RG Aile Strike. You can buy yours here. So far it is living up to expectations and building beautifully.

I have been looking at some of the Moderoid pre-orders. At the moment the following are on pre-order:

https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90583
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90587
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90267
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90647
https://www.cosmicgroup.eu/ing/action_figure_model_kit_bust_statue_gadget.php?id=90648

If you would like me to put in a pre-order to see if I can get any of them let me know!

That is is for “Advert / Stock 19/02/2023”, I will update further when I get more updates!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 18, 2023February 17, 2023 by Mark

RG Aile Strike Build Day 5

Introduction

Welcome back to “RG Aile Strike Build Day 5”! After yesterdays little break, I’m back with the latest update. For anyone catching up, I have made a few posts saying how fantastic I thought the RG Aile Strike model is. However, I hadn’t actually built one yet. So I decided it was time for me to put my money where my mouth was.

This series is documenting my build of the Aile Strike along with plenty of pictures.

The Update

Ok well today I was working on the other leg, as Day 4 was the first leg. As this is a carbon copy of the previous post (you can find it here) I didn’t do all the pre and post nub cleaning pictures. Feel free to check out yesterdays post to catch up on that. Again, I can’t say how great the Gray and White Balancers are from GUNPRIMER. They really help polish parts back up to a fantastic finish.

As you can see from the pictures these parts have also come together really nicely. So far the build hasn’t had anything other than nicely fit together sections. The detailing on the neg parts is brilliant, and I can’t wait to do the panel lining on this model. I think it might take me a while though with all those bits!

Conclusion

I believe the next part is the waist. I often find these sections some of the least interesting parts to build, so I am looking forward to seeing how this one holds up. So far, this build has been a pleasure, and the outer armour has been cleaning up beautifully. Possibly my only niggle so far is I could argue the feet feel a little weird. But once posed the look brilliant.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 15, 2023February 14, 2023 by Mark

RG Aile Strike Build Day 3

Introduction

Ok so I know this is called “RG Aile Strike Build Day 3” but I’ll be honest I wasn’t happy with the feet when I saw the pictures. So after spending hours sorting images, rotating them, re-sizing them, I then settled down with those darn feet!

What are they like now?

I started by stripping the feet back down. I took the front piece off to give easier access. Before starting on the red, I gave the rear grey pieces a fresh sandpaper. I wasn’t happy with how they were showing so I decided to do those again. After some sanding I applied the gray balancer, then the green side of the white balancer before finishing with the white side of the white balancer.

Once that was done I took apart the front of each foot. Those, to me, were the worst offending parts. I separated them so that I could get into the joint and sand them down further. I also used the zoom on my phone, along with a new LED lamp to help me see any of the imperfections. Once I was happy with the sanding I followed the same balancer routine as on the grey parts.

I don’t mind admitting I put them together and took them apart a couple of times and repeated the process until I was happy. I am determined this will not be a rush job. Interestingly this also gave me a better feel for taking the foot apart and re-assembling it.

Once I was happy with the front section I proceeded to sand the middle and rear sections. I left these in place as I didn’t have issues around their joints. Once I was happy with the new sanding I again applied the balancers to bring the shine back up.

Conclusion

I hope you will agree with me that they have a far nicer finish after the second round of cleaning up. I certainly am a lot happier. They polished nicely, and I also found that I managed to just make them look smoother.

I am definitely glad that I went back and re-did those parts. As I said this won’t be my fastest build, but it will be interesting to see the overall finish on the model.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 14, 2023February 13, 2023 by Mark

RG Aile Strike Build Day 2

Introduction

RG Aile Strike Build Day 2 covers what I managed to do in the first section of the build.

This build, unlike my “Guess the model” builds is going to be more evenly paced. As long as I have enough to warrant posting an update I will. Otherwise I’ll pickup a different topic and then follow on when there is a decent update.

What comes first

Well I already did a post about the tools, the box, the runners, and the manual. I even included a link to a PDF of the manual that I put together in case anyone is desperate to read the RG Aile Strike manual. You can find that post here.

So now that pre-amble is done, lets get on with the build!

First Bits

As you can see the main “bulk” part of the foot and ankle are cast as a single part. The ball joint is cast as part of this, and I still have no idea how they manage to cast a fully working ball joint! I then cleaned up the nubs and flipped the parts over. The smaller parts attach to the under side of the larger part. The fit together fairly snuggly, but once clipped in feel really nicely placed.

Second Bits

As you can see my first “rough” cut leaves a fair amount of nub. My second trimming cut leaves a much cleaner cut. At this point it is starting to look a bit better. After the second cut I then added some water to my wet and dry sandpaper and cleaned them down flush. Once I could run a finger nail over them without it catching I then did 5 passes with the Gray Balancer, 5 passes on the green side of the White Balancer, followed by 5 passes on the White side of the White Balancer. This left me with the “Cleaned Parts” picture. Any discolouration left is from the plastic / moulding and would need painting to hide. However the parts are smooth and shiny, just like they were on the runner!

I then needed to attach the parts. Each “foot” has a flat part which has a small plastic column that slots into a hole in the black piece. In “bottom plate fitted” above you can see one ready to be put in place and one attached. The cover / second piece (as you can see in the final photo) attaches to the 3 posts on the flat piece and clips firmly into place.

Third Bits

The next section was the middle section of the feet. As you can see I started with the wider cut, then the trimmed cut and finally the sanding and cleanup. Now I will say that these closeup pictures don’t, in my opinion, do them justice. However, as this isn’t a speed build I’m going to go back and clean them up even further to see how clean I can get them. As you can see the red piece attached from underneath, and the white piece then slots in on top. Once the white piece was lined up properly it slotted straight in.

Fourth Bits

Again as you can see, I went for the leave a nub, close cut the nubs off, then clean the pieces up. The heel consists of the flat piece that attaches underneath the foot onto a peg, and then the rear piece that curves around the heel and slots into place. Again, at the risk of sounding like a fan boy, these pieces go together really satisfyingly.

Fifth Bits

The final part of the foot was, in my opinion, the most fiddly. The two initial side pieces clip on to the sides of the grey piece. Then the final section slides over the top giving it more stability, and completing the stylistic look.

Conclusion

That concludes “RG Aile Strike Build Day 2”. However, as I said, I am going to revisit the feet. This isn’t a “fast” build, rather I want to see how clean a build I can make it.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 13, 2023February 12, 2023 by Mark

RG Aile Strike Build Day 1

Introduction

RG Aile Strike Build Day 1 is the first part in the RG build. In a previous post I said I needed to put my money where my mouth is and show off this model. I think it looks stunning, and I am really looking forward to this. I will post up the progress I make on this. However, unlike my “Guess the Model” series I won’t be ensuring I complete a section in a day. I will rather focus on more detail.

The setup

Before starting the build I wanted to show the box, parts tools, etc.

The Box

RG_Aile_Strike_Box_Contents — RG_Aile_Strike_Box

The box, like many RG boxes, is relatively compact. When you open it up you are greeted by the usual clear plastic packed Runners. I have to say I’m a little unsure as to why the runners are packed into clear plastic bags. It doesn’t seem to add anything. However, that is a different disccussion!

When you unpack everything you get to see what the kits is actually going to be made of.

As you can see the kit consists of 8 runners, a decal sheet (stickers) and the manual.

The runners

Here is a closeup of the individual runners and the decal sheet.

RG_Aile_Strike_Runner_B — RG_Aile_Strike_Runner_A

As you can see you have runners, A, B, C, D1, D2, E, F, and G. So far so good!

The Manual

Next up on the list of items is the RG Aile Strike Manual. This consists of 16 pages, including the front and rear cover.

RG_Aile_Strike_Manual_Page_02 — RG_Aile_Strike_Manual_Page_01

Although the manual only has 16 pages I added some closeups on the Decal page on the rear of the manual. I also ombined the above images into a single PDF that you can get here if you need it.

The Tools

Everything above covers the box, and its contents. Next up are the tools I plan on using to complete the build.

As you can see they are pretty standard fare. The Red handled nippers are for first cuts. The orange handled ones for the closer cut. The knife in case I need to shave anything closer. The 600 grit to smooth things down and the dropper bottle of water as it is wet and dry sandpaper so adding water prolongs the life of it. the Gunprimer balancers and brush for cleaning up after the nubs and removing particles from the balancers. The Oral-B to clean up bits from the model after sanding. Finally the tweezers and parts separator. The tweezers are to help me place decals, and the separator in case I need to split anything back apart.

I think, I will likely also use my panel lining pens and various top coat cans. I will include those when / if I use them.

Conclusion

I am really looking forward to this build. After all the bigging up I have done on how great I think it looks, I am super excited!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 12, 2023February 11, 2023 by Mark

Advert / Stock 12/02/2023

Welcome to “Advert / Stock 12/02/2023” this weeks update on any changes in stock and a blatant advert for the shop 😀

So I have had a mini box with a few items in this week which was nice. However, before I leap in there I should remind everyone, that if they are after this beast:

It is still (at the time of writing) available at the shop here.

So moving on from the Unicorn we have had some HG, MG and RG action this week!

I was fortunate enough to manage to snag a HG Age-2 Normal, and HG Age-3 Normal, as well as another Brady Hound to replenish stock there.

On the MG Side I got MG Astray Red Frame and MG Barbatos.

On the RG side of things I got the RG Aile Strike, RG Astray Red Frame, and RG Destiny.

This all is on top of the items I got last week!

Why not pop across to the shop https://modelkitsltd.co.uk/shop and have a browse on what we have in. If you want to jump to a specific topic/type of kit the links are below.

HG Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=hg

RG Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=rg

MG Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=mg

SD Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=sd

EG Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=eg

FM Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=full-mechanics

PG Kits
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=pg

Tools
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=tools

Bases
https://modelkitsltd.co.uk/shop/?swoof=1&product_cat=bases

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 11, 2023February 11, 2023 by Mark

Put my money where my mouth is!

Put my money where my mouth is! Ok that sounds like a click bait title. But let me explain!

So in my previous post I was banging on about how amazing I think the RG Aile Strike is. I also, in previous posts have banged on about how great I think the GUNPRIMER products are.

So to this end I have decided to quite literally put my money where my mouth is. My next series of posts are going to be centred around the RG Aile Strike.

What is the plan I hear you cry. Well I think it is time to start showing off everything start to finish.

Step one is the prep. I have just ordered what I hope will be a workable mini green screen style box to improve my sometimes shonky photos. I will also pop to my storage and pickup an RG Aile Strike for the build. I already have the GUNPRIMER Gray and White Balancers here so that gets it ready to go.

From all the images this looks to be a truly outstanding model. So I thought why not take people through the build, and give honest feedback on the whole process. This isn’t going to be a rushed job, and I will have to take slight detours from time to time. However, hopefully, the end result will show what a fantastic model this is.

For anyone interested you can pickup the model in the shop (at the time of writing) here.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 10, 2023February 9, 2023 by Mark

RG Gundam Aile Strike 1/144

Introduction

I currently have a box in my living room. In that box should be 5 RG Gundam Aile Strike models. I picked them up partially because I think they look amazing, and partially because I may nab one for myself!

If you haven’t seen it the model looks like this:

Background

The model was originally released in April 2011 and featured the latest advancements in joint technology. It was also the 3rd model released in the commemoration of 30 years of Gunpla.

The suit itself was first introduced in Gundam Seed (a show I still need to watch despite having already watched Gundam Seed Destiny … yes I know the wrong order:) ). It was originally piloted by Kita Yamato.

If you want to see a full detail of the kit, and the parts, and the general makup have a look at the information on dalong.net. Note you will want to have your translation software/plugin/extension of choice to hand unless you happen to read Korean.

One of the items I found interesting reading through the information there, is that like other RG models the hand consists of multiple parts. As a result this leads to it being split into a palm, the thumb as it’s own jointed part, the index finger as it’s own jointed part, and the middle, ring and little fingers all forming the final jointed part. Subsequently the separation provides a much larger range of posing and options with the hand. It is one of the items I find absolutely amazing with these kits.

Conclusion

As can be seen by looking at the model images, and the quite comprehensive images on the dalong website I think this looks like a phenomenal kit. The little details, like the styling on the shield, and the slightly tapered in calf / lower leg, all give this a really unique and stylish look. As a result I think I may just be talking myself into getting one into my backlog!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 9, 2023February 8, 2023 by Mark

Custom Decals – My First Attempt

Introduction

I was curious, about making some custom decals. Now this wasn’t a case of I had to, this was purely an experiment. As the sticks are sometimes a bit jarring when they are applied, I thought I would look at how hard it would be to make my own decals.

Tools of the trade

After some research I found that really, you don’t need a lot of things to do this.

Water slide decal paper
A printer (suitable for use with the paper you bought)
A graphics application
Some topcoat

Water Slide decal paper can be bought online. It isn’t the cheapest, and it normally stipulates what type of printer it works with (for example inkjet). The printer, topcoat and graphics application I actually already had. So the only thing I had to buy specifically for this was the paper.

For the graphics manipulation I chose to use GIMP (available here) as it is free, and there are plenty of online tutorials that can help you get the best from it.

Making the images

To create my sample page / decals I decided to do some googling. I found some great examples that I used as inspiration for creating my first sheet. The final A4 page looked like this:

I realise there is a lot of wasted paper here but I just wanted to test it all out. Next I used the waterslide paper I purchased off ebay and printed the above image onto it.

I left it overnight then just to make sure the ink had dried. I realise this is overkill, but I wasn’t in a rush.

The next step was to apply top coat to the sheet. I opted for 3 coats leaving it well over 10 minutes between each coat.

I finally had my sheet to try!

Testing

Ok I won’t lie. My first test was a disaster. But I think that was more to do with me not understanding how to apply them, and less to do with the decal. Applying them was, once I had some practice, easy enough. I ended up adding some to my heavy arms leg launchers.

On the images above the little nuclear sign, and the red triangle and “caution” sign on the left image were custom ones from my print. The one on the image to the right is also a custom one.

Conclusion

All told I think the experiment was a success. I definitely found they worked best on lighter/white backgrounds but other than that I was very happy with the end result.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Cookie	Duration	Description
cookielawinfo-checkbox-analytics	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics".
cookielawinfo-checkbox-functional	11 months	The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional".
cookielawinfo-checkbox-necessary	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".
cookielawinfo-checkbox-others	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other.
cookielawinfo-checkbox-performance	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance".
viewed_cookie_policy	11 months	The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.

Introduction

The process

First Parts

Second Parts

Third Parts

Fourth Parts

The final leg

Conclusion

Introduction

The Update

Conclusion

Introduction

What are they like now?

Conclusion

Introduction

What comes first

First Bits

Second Bits

Third Bits

Fourth Bits

Fifth Bits

Conclusion

Introduction

The runners

The Manual

The Tools

Conclusion

Introduction

Background

Conclusion

Introduction

Tools of the trade

Making the images

Testing

Conclusion

Recent Posts

Recent Comments

Archives

Categories