Build Archives - ModelKitsLtd.co.uk

Posted on March 7, 2023March 6, 2023 by Mark

RG Aile Strike Build Day 11

Introduction

Welcome to “RG Aile Strike Build Day 11” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

I am taking my time to ensure I clean up all the marks that can be cleaned up. As with any build like this, if you end up with discolouration or a small white “stress” mark you are likely to need painting to get rid of those. I may have a look at simple quick methods of dealing with those items, especially as I find that it has a habit of happening on the grey pieces. I also accept I may need to work on my cutting style as I’m sure that will contribute to it!

The Process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

The Parts

I had pre-removed the parts and put them in the small bag. The head consists of 14 parts, some of which are quite small. The really small red pieces I found quite tricky to hold on to and they had a habit of pinging away from me. However, once the cleanup was complete I was, as with the rest of the mode, very happy with the final result. The parts themselves clean up beautifully, and using the GUNPRIMER balancers they look like they were never touched.

Part Build

I took this picture part way through building the head. Lots of the pieces layer on top of one another, and I thought this was a great view of the partly built head. I may yet need to dismantle it if I find suitable waterslide decals. I will, however, cross that bridge when I come to it.

The Build So Far

With the head complete, and in place, most of the model is done. I have him currently dabbing while next to Heavyarms and DoubleX. I don’t know why I just did.

Conclusion

So far the build has been extremely satisfying. The only glitches have been user error on my part. The parts clean up really nicely, and you can achieve a really nice finish on the model. I still have the weapons and backpack to build. Once that is done I will top coat, panel line and top coat again. Hopefully I will then be able to take some photos that do the model justice!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on March 2, 2023March 1, 2023 by Mark

RG Aile Strike Build Day 10

Introduction

Welcome to “RG Aile Strike Build Day 10” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

The Process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

The Parts

There are approximately 27 parts to the torso. However, you do need the two joint parts that were extracted from the top of the arm skeletons.

For the image above I cut the pieces out roughly and then put them into a small plastic bag overnight. No reason other than I was working on a few things 🙂

Cleaned Parts

I cleaned up the parts using the process outlined about. I also at this point have no idea what order I am going to need them. However, it wasn’t a massive problem. I will, however, note that the two white pieces of armour have a slot on the inner piece that goes to the front or back depending on what side you attach them. This is important as the longish white piece (on the top line of pieces third from the top left, and surrounded by blue pieces), fits into those slots. I found out that if you attach those on the wrong side then you have to take it apart again (2 pieces on top of them) and refit.

This was because I decided to give myself a blast from the past, and just put them all together in a bag. It reminded me of the old lego bags where all the parts for a specific section of the build were all together. This looked like this.

I actually enjoyed identifying the pieces from the manual and then finding them in my pile 🙂 Ultimately you should have a build process that you enjoy.

Putting it together

Once the torso was built I was able to attach the legs and arms. I then had a play with the posing on what I had so far. The articulation is great on the model. The “trying to do the splits” is limited due to the side parts that limit it. However, there is more than enough there to pose in a range of stances.

Also, as you can see from the pictures, at the moment the model can balance amazingly. With a little patience we can balance it really nicely.

Conclusion

I am still really happy with this. The model is building amazingly, and the way the parts layer up is really satisfying. The detail and articulation on this model are also fantastic. If you then add to this the great way the parts can clean up it is shaping up to meet all my expectations.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on March 1, 2023February 28, 2023 by Mark

RG Aile Strike Build Day 9

Introduction

Welcome to “RG Aile Strike Build Day 9” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

The Process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

The Parts

As you can see the arm consists of 16 core pieces. Above I have just cut them out roughly ready for trimming and cleaning up. I showed that in the previous arm, so in this post I’m going to show you something different about them.

The arm Skeleton

All pieces straight — Joint and Fist Separated

On the inside you have a lovely inner frame. The frame or skeleton comes pre-case on the runner. I find it mind boggling how they cast these intricate pieces.

In the first image you can see that the fist and joint have been separated. They come attached, but you need to remove them. The top joint is actually part of the shoulder assembly used when you build the torso. The fist is just re-attached later on. Previously I had issues removing the top part, however, knowing it was a straight peg I felt far more confident twisting and pulling to free the part. I found removing it on this arm a lot easier than on the first one.

In the second image (incorrectly titled all pieces straight) I had rotated and bent the socket joint into place.

The third image then has a small piece on the left hand side of the image bent upwards. Ultimately this clips back onto the central core of the arms frame. You can see this in the next image (“Bending into place”) how the section is bending up back towards the central part of the arm frame.

The “Top connected” picture shows the left hand piece completing the motion up and clicking into place into the frame, as well as the bottom section starting to bend down.

The final image has the arm frame complete with the part the fist was attached to moved all the way flat with the rest of the frame, and in place.

The finished Arm

As with the other pictures (yes I know I need a better background, I am working on it honest!) you can see how the armour has cleaned up nicely. I am really happy again with how this fits together. I really enjoy building the arms on this model as it is a satisfying process.

Conclusion

Everything in the build process, so far, has lived up to my expectations. The detail is stunning, the precision is what I expect from Bandai, and the build itself is an incredibly enjoyable process.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 25, 2023February 25, 2023 by Mark

A Mixed Bag

Introduction

Ok well, this should have been the next part of the Aile Strike build. However, procrastination, and the delivery of a second hand 3d printer both got in the way, making this a mixed bag! Then there was a few episodes of Knight’s and Magic on Crunchyroll.

So what have I been doing?

Thing I was doing Saturday

Well I did start to prep parts for the build. In fact here is the proof!

This little bag contains all the bits I need to build the next arm. I need to do the second cut wit the nippers, the clean-up, the final polish and assembly. They got cut out with the intention of me working on them this evening. However I just sort of had a nap and then struggled to get started again. However, tomorrow is another day!

What else have I been doing?

As you may, or may not, be aware, I listed some reasonably priced basic 1/144 bases recently. You can find them here. They are only £2 each a real bargain! However, I have been working on creating some 3d models to print for adapters to add to them as additions so that you can benefit from different adapter types if you want them.

Here is my first experiment.

As you can see it is in the planning and test phase at the moment. This version fits the double strike really nicely. I am, however, having issues with print consistency. Tomorrow I should have a new delivery of filament which I am hoping may resolve that problem. Being new to the whole 3d printing world, this is a whole new thing.

Once I manage to get the printer printing consistently, next will be testing various different sizes, shapes etc. to find what work best. As soon as I am happy with them they will go up as an optional add on to the stands. Current thinking is that the adapter would be something like 50p.

Conclusion

Apart from watching my 3d printer not do what I want it do, I did get some parts rough cut out. Hopefully tomorrow will be a more productive modelling day!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 21, 2023February 22, 2023 by Mark

RG Aile Strike Build Day 7

Introduction

Welcome to “RG Aile Strike Build Day 7” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

Round about now you are probably thinking to yourself … blimey he is not a fast builder I would have had that done days ago! However, in my defence I am working full time, plus running my company, and then building after I have done everything for those. I am also really taking my time, and if I’m not happy re-visiting parts and re-doing them. I used to take months to paint a single model, to the point where my friend offers to paint them for me so that he can play against painted minis 😀 (Thank you Steve 🙂 )

So my normal steady pace aside, I do want to really enjoy the build and not rush at any stage. I want to show how stunning the model is, not just to build, but how beautifully clean it looks once complete.

Without further ado, lets just outline my process on each part so that I don’t repeat is throughout the post 🙂

The Process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

So this section is the build up of the arms. The first thing I had to do was build up the two shoulders. Then it steps into building each arm individually. The core of the shoulder is really simple but the plastic cleans up from the nubs really nicely and fits together nicely.

Second Parts

Next up is the armour that wraps around the core of the shoulders. Now I love these shite armour pieces. With the GUNPRIMER Balancers they clean up so nicely and shine back up to new. The pictures show how clean these pieces end up after a little TLC even given those horrendous first rough cuts of mine!

Third Parts

Ok there is no running away from it. These are, for me at least, not my favourite part of any build. I can, however, appreciate the quality and skill that has gone into making these pieces. The articulation and the fact they are moulded like this on the runner.

However, I just don’t like these bits. Thankfully once they are done it will be back to the bits I enjoy. The first image shows exactly how the piece comes off the runner. Pay very close attention to the manual, and where it says to cut. I then had to detach the hand, and the top part.

As you can see I managed to detach more than I was meant to, so I had to reattach the joint. However, I really didn’t enjoy getting the top piece out. Once that was done, all I had to do was twizzle and push bits into place. I have to admit I do enjoy that bit.

You have to pay special attention to the piece that in the first image is on the right hand side. That teeny piece actually bends in the middle, and the outer piece actually forms the part that clicks into place when you bend the rest up.

Fourth Parts

Ok so this was the last bit I got to work on. The upper arm armour. Again, this shows the detail, the layering of parts to add more detail, and the beautiful way the parts clean up. I know I have said it before but, I am very happy with the way this has been cleaning up so far!

Conclusion

I am really enjoying the build, and the pace. The parts are cleaning up beautifully and the parts are all cleaning up so nicely. That concludes “RG Aile Strike Build Day 7”.

If you wanted to pick up an RG Aile Strike to do the build yourself at the time of writing I have a few in stock available here. I also currently have both the Gray and White Balancers in stock (Gray White).

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 20, 2023February 19, 2023 by Mark

RG Aile Strike Build Day 6

Introduction

Welcome to “RG Aile Strike Build Day 6” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

If you want to skip that and just get up to speed. I had in previous posts gone on about how nice I think the RG Aile strike model is. I had gone on so much I decided I should put my money where my mouth was and build one myself. This ongoing series is that process. I am not rushing, as can be seen in the earlier parts, and if I am not happy I will go back, disassemble and re-clean and re-build anything I am not happy with.

With that all out of the way lets get to it!

The process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

Waist and detached thingy — Waist and thingy

So the first part off the runners is the main body of the waist. It has this piece attached / in it in the runner. The manual has an arrow showing to pull that piece out. I’ll be honest that was the hardest part of the build so far. With how detailed the pieces are I was worried about breaking it. In the end I decided to spin and twist. The turning of the part helped free it up and eventually it came out. However, I could see it causing a problem for some younger builders. However, on the whole it wasn’t “bad”.

Second Parts

Next up was the start of building up the armour on the waist. Now these pieces were nice and therapeutic. I used the process above, and am extremely happy with how the armour is coming out on this model.

Third Parts

Again, the armour is building up nicely. Even the small blue piece cleaned up perfectly. The grey piece looks a lot cleaner after a brush btw (sorry about that). However the nubs are a thing of the past and the piece looks really clean. None of the parts have had any issues going together and feel really nice.

Fourth Parts

I found these parts really satisfying to put together. There aren’t too many of them, and the slight colour differences on some of them add a nice level of contrast. They click together nicely and come together really cleanly.

The final leg

Putting all these things together you can see you have a really striking lower part of the model. All of the pieces so far have been really enjoyable to clean up and put together. There is a center grey piece that goes on top of the main waist part. I admit that is my least favourite part so far. It doesn’t want to clean up properly and just feels very meh. That part has some twisty around pre cast joints that click on to outer side armour. That goes in really snugly once you get it to click in, but getting it to click in was the “hardest” part of the build so far. However, that all said it wasn’t really hard.

Conclusion

That concludes todays “RG Aile Strike Build Day 6”. Remember if you want the model it is available (at time of writing) here.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 16, 2023February 15, 2023 by Mark

RG Aile Strike Build Day 4

Introduction

Welcome to “RG Aile Strike Build Day 4” where I am building up an RG Aile strike model. If you haven’t read any of the other parts I would recommend going back to the start. You can find that here. In the first post I covered the box, runners and provide the manual.

With that all out of the way lets get to it!

The process

Unless otherwise noted I followed this process for each piece:

Cut off roughly leaving plenty of nub
Trim back the nub with my better nippers
Apply water to my wet and dry sandpaper and sand the nub marks down
Dry the piece
Brush it off with the tooth brush to remove any bits
Re-apply the matt finish using the Gray Balancer
Prep the part with the green side of the White Balancer
Shine the part up with the white side of the White Balancer

If after this I wasn’t happy I would repeat the sanding steps down, and keep iterating until I was happy with the finish.

First Parts

As you can see the next thing to build was this leg. The inner frame is straight off the runner. You need to take your time on this. The manual shows you the bits you want to cut. Pay special attention to this as the nubs are tiny and you don’t want to snip anything by accident. The first two parts go on either side of the leg. They clip right on and fit really nicely.

Second Parts

The next pieces start to attach the armour. As you can see I was leaving healthy nubbage on each piece. I followed the process outlined at the top of the article. Once clean, and seated I moved on to the next armour parts.

Third Parts

As you can see this section is adding more armour on to the frame. Each piece fits really nicely. I did have to slow down and double check how everything was sliding in to place. But after slowing myself down a little it all slotted together really nicely. Again I was really happy with how the white armour pieces were cleaning up.

Fourth Parts

Next … you guessed it more armour parts. Each one I’ve tried to show the nubbed parts and the cleaned parts. Hopefully the end result warrants all this time … I feel that it is looking really nice so far.

Fifth Part

The final set of armour pieces on the leg really do complete the piece. Also look at that articulation!

Conclusion

There are several parts here that have to slide or clip into specific places. However, I found that slowing down, have a close look at the manual, the structure of the grooves and ridges on the parts led to them fitting together beautifully. I am really happy with how the parts have cleaned up, and the current state of the leg.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 15, 2023February 14, 2023 by Mark

RG Aile Strike Build Day 3

Introduction

Ok so I know this is called “RG Aile Strike Build Day 3” but I’ll be honest I wasn’t happy with the feet when I saw the pictures. So after spending hours sorting images, rotating them, re-sizing them, I then settled down with those darn feet!

What are they like now?

I started by stripping the feet back down. I took the front piece off to give easier access. Before starting on the red, I gave the rear grey pieces a fresh sandpaper. I wasn’t happy with how they were showing so I decided to do those again. After some sanding I applied the gray balancer, then the green side of the white balancer before finishing with the white side of the white balancer.

Once that was done I took apart the front of each foot. Those, to me, were the worst offending parts. I separated them so that I could get into the joint and sand them down further. I also used the zoom on my phone, along with a new LED lamp to help me see any of the imperfections. Once I was happy with the sanding I followed the same balancer routine as on the grey parts.

I don’t mind admitting I put them together and took them apart a couple of times and repeated the process until I was happy. I am determined this will not be a rush job. Interestingly this also gave me a better feel for taking the foot apart and re-assembling it.

Once I was happy with the front section I proceeded to sand the middle and rear sections. I left these in place as I didn’t have issues around their joints. Once I was happy with the new sanding I again applied the balancers to bring the shine back up.

Conclusion

I hope you will agree with me that they have a far nicer finish after the second round of cleaning up. I certainly am a lot happier. They polished nicely, and I also found that I managed to just make them look smoother.

I am definitely glad that I went back and re-did those parts. As I said this won’t be my fastest build, but it will be interesting to see the overall finish on the model.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 14, 2023February 13, 2023 by Mark

RG Aile Strike Build Day 2

Introduction

RG Aile Strike Build Day 2 covers what I managed to do in the first section of the build.

This build, unlike my “Guess the model” builds is going to be more evenly paced. As long as I have enough to warrant posting an update I will. Otherwise I’ll pickup a different topic and then follow on when there is a decent update.

What comes first

Well I already did a post about the tools, the box, the runners, and the manual. I even included a link to a PDF of the manual that I put together in case anyone is desperate to read the RG Aile Strike manual. You can find that post here.

So now that pre-amble is done, lets get on with the build!

First Bits

As you can see the main “bulk” part of the foot and ankle are cast as a single part. The ball joint is cast as part of this, and I still have no idea how they manage to cast a fully working ball joint! I then cleaned up the nubs and flipped the parts over. The smaller parts attach to the under side of the larger part. The fit together fairly snuggly, but once clipped in feel really nicely placed.

Second Bits

As you can see my first “rough” cut leaves a fair amount of nub. My second trimming cut leaves a much cleaner cut. At this point it is starting to look a bit better. After the second cut I then added some water to my wet and dry sandpaper and cleaned them down flush. Once I could run a finger nail over them without it catching I then did 5 passes with the Gray Balancer, 5 passes on the green side of the White Balancer, followed by 5 passes on the White side of the White Balancer. This left me with the “Cleaned Parts” picture. Any discolouration left is from the plastic / moulding and would need painting to hide. However the parts are smooth and shiny, just like they were on the runner!

I then needed to attach the parts. Each “foot” has a flat part which has a small plastic column that slots into a hole in the black piece. In “bottom plate fitted” above you can see one ready to be put in place and one attached. The cover / second piece (as you can see in the final photo) attaches to the 3 posts on the flat piece and clips firmly into place.

Third Bits

The next section was the middle section of the feet. As you can see I started with the wider cut, then the trimmed cut and finally the sanding and cleanup. Now I will say that these closeup pictures don’t, in my opinion, do them justice. However, as this isn’t a speed build I’m going to go back and clean them up even further to see how clean I can get them. As you can see the red piece attached from underneath, and the white piece then slots in on top. Once the white piece was lined up properly it slotted straight in.

Fourth Bits

Again as you can see, I went for the leave a nub, close cut the nubs off, then clean the pieces up. The heel consists of the flat piece that attaches underneath the foot onto a peg, and then the rear piece that curves around the heel and slots into place. Again, at the risk of sounding like a fan boy, these pieces go together really satisfyingly.

Fifth Bits

The final part of the foot was, in my opinion, the most fiddly. The two initial side pieces clip on to the sides of the grey piece. Then the final section slides over the top giving it more stability, and completing the stylistic look.

Conclusion

That concludes “RG Aile Strike Build Day 2”. However, as I said, I am going to revisit the feet. This isn’t a “fast” build, rather I want to see how clean a build I can make it.

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Posted on February 13, 2023February 12, 2023 by Mark

RG Aile Strike Build Day 1

Introduction

RG Aile Strike Build Day 1 is the first part in the RG build. In a previous post I said I needed to put my money where my mouth is and show off this model. I think it looks stunning, and I am really looking forward to this. I will post up the progress I make on this. However, unlike my “Guess the Model” series I won’t be ensuring I complete a section in a day. I will rather focus on more detail.

The setup

Before starting the build I wanted to show the box, parts tools, etc.

The Box

RG_Aile_Strike_Box_Contents — RG_Aile_Strike_Box

The box, like many RG boxes, is relatively compact. When you open it up you are greeted by the usual clear plastic packed Runners. I have to say I’m a little unsure as to why the runners are packed into clear plastic bags. It doesn’t seem to add anything. However, that is a different disccussion!

When you unpack everything you get to see what the kits is actually going to be made of.

As you can see the kit consists of 8 runners, a decal sheet (stickers) and the manual.

The runners

Here is a closeup of the individual runners and the decal sheet.

RG_Aile_Strike_Runner_B — RG_Aile_Strike_Runner_A

As you can see you have runners, A, B, C, D1, D2, E, F, and G. So far so good!

The Manual

Next up on the list of items is the RG Aile Strike Manual. This consists of 16 pages, including the front and rear cover.

RG_Aile_Strike_Manual_Page_02 — RG_Aile_Strike_Manual_Page_01

Although the manual only has 16 pages I added some closeups on the Decal page on the rear of the manual. I also ombined the above images into a single PDF that you can get here if you need it.

The Tools

Everything above covers the box, and its contents. Next up are the tools I plan on using to complete the build.

As you can see they are pretty standard fare. The Red handled nippers are for first cuts. The orange handled ones for the closer cut. The knife in case I need to shave anything closer. The 600 grit to smooth things down and the dropper bottle of water as it is wet and dry sandpaper so adding water prolongs the life of it. the Gunprimer balancers and brush for cleaning up after the nubs and removing particles from the balancers. The Oral-B to clean up bits from the model after sanding. Finally the tweezers and parts separator. The tweezers are to help me place decals, and the separator in case I need to split anything back apart.

I think, I will likely also use my panel lining pens and various top coat cans. I will include those when / if I use them.

Conclusion

I am really looking forward to this build. After all the bigging up I have done on how great I think it looks, I am super excited!

Thank you for taking the time to read this. If you haven’t already done so please like and follow us on our social media platforms and checkout our website!

Facebook: https://www.facebook.com/profile.php?id=100086701512793
Instagram: https://www.instagram.com/modelkitsltd/
Website: https://modelkitsltd.co.uk

Cookie	Duration	Description
cookielawinfo-checkbox-analytics	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics".
cookielawinfo-checkbox-functional	11 months	The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional".
cookielawinfo-checkbox-necessary	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".
cookielawinfo-checkbox-others	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other.
cookielawinfo-checkbox-performance	11 months	This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance".
viewed_cookie_policy	11 months	The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.

Introduction

The Process

The Parts

Part Build

The Build So Far

Conclusion

Introduction

The Process

The Parts

Cleaned Parts

Putting it together

Conclusion

Introduction

The Process

The Parts

The arm Skeleton

The finished Arm

Conclusion

Introduction

So what have I been doing?

What else have I been doing?

Conclusion

Introduction

The Process

First Parts

Second Parts

Third Parts

Fourth Parts

Conclusion

Introduction

The process

First Parts

Second Parts

Third Parts

Fourth Parts

The final leg

Conclusion

Introduction

The process

First Parts

Second Parts

Third Parts

Fourth Parts

Fifth Part

Conclusion

Introduction

What are they like now?

Conclusion

Introduction

What comes first

First Bits

Second Bits

Third Bits

Fourth Bits

Fifth Bits

Conclusion

Introduction

The runners

The Manual

The Tools

Conclusion

Recent Posts

Recent Comments

Archives

Categories